Need Help! Shaking Problem On My Laser Machine
Hello I just bought this Laser/Engraving Machine I used 2 days and everything was perfect Today when it was cutting it started to shake when the Y axis try to move. Its not moving at all. here is the...
View ArticleClik here to view.
VAC III error in LB15IIM
Hello. I have a machine that was turned on once and it booted, had a few errors - it was the first time that was connected here, and no coolant was in the machine and so on - so I suspect it was...
View ArticleNeed Help! G54 problem with mill
Fanuc 15ma mill control problem I'm new to G code & need help with G54 . Every time i enter G54 in program ,then hit enter table takes off for limits ? If I'm in middle of table and set G54 to...
View ArticleProblem Multi_Start Thread using G76
Never programmed one before... Need to program a 3/8-16 2-start, and 4-start (for engagement comparison) external thread using G76. Can someone give me a block of code? Thanks!
View Articlecutter squeal case emergency stop message
Hi i have a interact one mark 2 of 1994 vintage with a 2500B controller and have a problen when either 3D milling or pocketing when the cutter starts to squeal when for instance if pocketing milling...
View ArticleEarly Haas VF manual for Christmas?
Want to say Merry Christmas to all! If someone is looking for a Haas manual for the older plastic housing Haas VF series mills, here is one on eBay. Still no bids at 99 cents and 11.00 shipping. Ending...
View ArticleClik here to view.
Archtop done!
Hi All, This is the Archtop I just completed (Need some final touches, like a truss rod cover, tuning peg alignment etc). The top is Sitka Spruce, and the back and sides soft maple...Cocobolo for the...
View ArticleClik here to view.
Spindle operation
OI am setting up a used cnc I bought. I have struggled through getting the axeis to move but got x y z working. I can load a g code into mach3 and get it to run correctly. I can not get spindle to turn...
View ArticleClik here to view.
Alarm 121 on a Haas TM-1P 2009 Model
I'm having an error for an alarm 121 on a 2009 Haas Toolroom Mill (TM-1P) To give the background story, this mill has been sitting idle for maybe two years at this point. I started bringing this mill...
View ArticleNeed Help! Hot wire electronic
Hi! I will be build an CNC for hotwire styro cutting. electronic will be like this: http://www.ebay.com/itm/USA-Ship-Fre...item2a2758c1ad i want to regulate a temperature of wire.. how i cane regulate...
View ArticleClik here to view.
Need Help! 3 phase motor wiring help
Hello all, i'm hoping for some assistance in wiring up a 3phase motor to a VFD. I cannot find a wiring diagram for this motor, which is a Euronorm H 71-2 as near as i can figure. Two things are...
View ArticleClik here to view.
Need Help! Making Propellers
I want to cut out some props on my CNC. The whole 3D seems very complicated and I cant get any real info on how to do despite spending a Sunday on the PC looking. In the past someone on here (I think)...
View ArticleSoftware questions
I Have a old flashcut Signal generator flashcut cnc 401A servo control box limit switch wiring/switches 3 servo motor cables 10' control pendant and that's all I got when I purchased it at a...
View ArticleSpeed Controller
My mini lathe started out as an HF 7x8 (billed as a 7x10), and I converted it to a 7x14. I never felt the screw that came with the 7X14 bed mated up properly with the grip nut on the carriage, so the...
View ArticleClik here to view.
HOBBYCNC PRO 4 AXIS Built tested 100%
Not sure if I can post this here or not. If wrong place please move. I have a hobbycnc pro with the 4th axis. Built and tested. I bought a few of these a few months back and this is the only one I have...
View ArticleNewbie RS232 COMM
well i have been at this for 3 weeks now with no luck. you name it i have tryed it i have tryed every baud rate ,bit,parity,bla bla blaa, on .contoller,preditor,and serial adapter,i have read every...
View ArticleA2100 BIOS Battery Replacement
I am going to replace both the WS and RT batteries in my 1996 Sabre 750 this coming week. I am not yet having any problems, so this is strictly preventative maintenance. I am planning to do it on...
View ArticleClik here to view.
Stuck.. Advice?
Making a part in X4 that I'll do on my Tormach. I've got some of the ops done in the order I want to do them. My next cut is to cut the perimeter of the part (except the major radius to the right as...
View ArticleHow to cut gears with 4 axe operation. Help please ?
Hi Just finished my 4th axe and wanted to make a g code to cut a gear on a mill with a gear cutter disc. This means that i have to change somehow the Z axis with the Y axis . The rotation is on X axis....
View Articlemeldas 500 problem
We have leadwell V40 vertical machining center with meldas 500 system , and control unit model meldas FCA50M , when we open the machine that control unit display flashing AL 91 then 80, 00 goes like...
View Article