Warning to potential buyers of RhinoCAM
When I was first shopping for software several years ago I decided on RhinoCAM but almost did not buy it because it needed a dongle and they will not replace a lost dongle. You need to repurchase the...
View ArticleKITAMURA 630i rotation of pallet
We have 2 kitamura Horz mills both 630i's...One machine rotates to for example B10. in the shortest distance. The other machine will B10. will rotate all the way around to get to this number....Whats...
View ArticleWhat program and how?
Hope I'm in the right place. I want to inkjet print a linear scale on decal material to apply on a cylinder; degree marks. My problem is how to draw it and what program to use. I can array lines but...
View ArticleNeed Help! DIY cable carrier
:mad: Can anyone help! Looking for dxf file for a cable carrier about 3" wide.:rolleyes:
View ArticleFanuc 21i-T problem feeding into shaft
My first time posting here, so bear with me. I have a Romi M-27 with a Fanuc 21i-T control that I program conversationally. Last year I had a problem when I was running a simple 3 or 4 diameter step...
View ArticleMisc:
1. I keep seeing this snippet of broken code at the top of the page when I enter the forums. Code: ');Â Â Â Â var sidebar_align = 'left';Â Â Â Â var content_container_margin = parseInt('290px');...
View ArticleSprutcam 8 - No Chip Thinning Compensation?
In feeds and speeds you can set the feed per tooth which is very handy and saves on math. But it appears sprut is taking the easy way out and setting a feed rate based on a full width cut and...
View ArticleBarfeeder Timeout
How do I change the value of a timer on my 2600sy fanuc 31i-a control? It is set to 20 seconds by default and it takes longer then that to load a bar.
View Articlecnc contract programming
Hi I'm a contract programmer if anyone needs some programming done contact me. I have 28 years experience of machining and programming and I'm available 24/7.
View ArticleNeed Help! G. Weike LC1512 Importing to US
Hi, I've purchased a G. Weike LC1512 and the boat is about 2 days out of port. I've just been asked for the FDA doc and discovered what I have appears to be a CE doc. I've emailed my contact at G....
View ArticleWcs issue.
Guys. I need to work out how to get x5 to output a stop when it changes from say a g54 to a g55 wcs. Bad to worry about if before but I now have a job that requires a chamfer on both side of the stock...
View ArticleProblem internal 1 1/2" -11 1/2 tpi npt thread cycle G&^
wondering if any one could help with the bore size and final x position calculation for the above thread the thread i am using is 1" long and i will start say .200" off the face of the job i plan to...
View ArticleNeed Help! VM1 Error msg - OVERLOAD FAULT
Hello everyone. I have a problem with my VM1. Today, all of the sudden , as a program was running perfectly normal, it interrupted, by an error msg : "OVERLOAD FAULT - RESET OVERLOAD FAULT " There is...
View ArticleMakerSlide EastEurope
Hello, My name is Laurentiu, and for the last year and more i am following this forum and the buildlog.net.Recently i have bought an eShapeoko from MakerSlideEurope that i'm very happy with it(very...
View Articleaffordable titanium investment casters?
I have a product that I need made, I would really like to keep this in the US if I can find someplace to cast this that is reasonable. The geometry is not that complicated and part weight is about 1.4...
View ArticleSolved V24 Getting Started for Plasma Cutting
This video walks though setting up the V24 software for plasma cutting. Showing you how to change the screen interface, general navigation of the software and programming a sample part.
View ArticleProblem cutting the Escape gear
Im having a terrible time with the escape gear, even though the gear is faily large 10", the teeth are very sharp at the tips, have tried several different methods of cutting with the same results,...
View ArticleNeed Help! Need Help - - - Serpantine belt dimensions print. ( 6 RIB) Gates /...
I had a print from Gates or Goodyear in the past with the dimensions for the 6 rib serpentine belt. If anyone can help me find it again that would be great. Thanks, MrRogue MrRogue1@yahoo.com
View ArticleIntelligent Actuator
http://www.ebay.com/itm/181025284421...84.m1423.l2649 I just bought an actuator like this one currently listed on Ebay, does anyone know anything about it, the part number is very hard to read, looks...
View ArticleProblem Looking for spare parts for out router
Our machine uses(3) Slo-Syn KML092F-102 motors. If you have them for sale please reply for further discussion
View Article