Need Help! Precix 9100 -Copley Controls 800-700 Servo Motor amplifier went bad
I have a servo motor amplifier (Copley Controls Model 800-760) that went bad in my Precix 9100 router. I have put my only spare in the controller. Is there another model that will work? Eventually I...
View ArticleNeed Help! series 1 2 hp grinding speed change plate
I have 2 series 1 2hp variable speed bridgeports and both were running loud and one wouldn't adjust speed over 200 rpms without hitting the speed change plate. I tore apart the just loud one apart...
View ArticleNewbie DIY CNC Table Saw Build?
Has anyone tried to build a CNC table saw for short run production jobs? I haven't had time to put pen to paper but I have a few ideas on how to get it accomplished. Looking to build a machine for...
View ArticleNeed Help! Fagor 8025TG and WinDNC
I am not having any luck connecting my 8025TG controller to a PC using WinDNC. I have tried lots of different configurations on the PC and controller searched for answers on the web and still am not...
View ArticleAnyone familiar with this bandsaw?
Femi 782XL Benchtop Metal Cutting Utility Band Saw | eBay Right now I have the Grizzly porta-band, and it sucks. I need something small, but also sturdy enough to make straight cuts and mitre'd cuts....
View ArticleNeed Help! Fanuc: 9000: SPN1: S-SPINDLE ERROR (AL-00)[X]
I am climb milling with a 5.0" slotting cutter and am getting this error when exiting one part and entering another. .500" depth of cut, .3125 width of cut, ductile cast, 382rpm, 7.0 ipm. I was...
View ArticleNeed Help! Moxa NPort and Burny 2.5 Plus
Hi! I am a newbie, and hope someone can give me some advice.... I intend to replace an old manual serial switch who connects two Burny controlled CNC cutting maschines to a computer. I was looking at...
View ArticleClik here to view.
Need Help! Help in making thread
Good evening gentlemen of CNC! I need to make a thread of images in Okuma lathe, can someone help me?
View ArticleHELP!!! DYNA 3300-B Lathe with Mitsubishi Meldas 50L
Hello Guyz; I'm trying to run a Dyna 3300-B lathe with mitsubishi Meldas 50L/50G control. I don't have the operation manual nor the programming manual, PLEASE! can someone help me with the information...
View ArticleOffer USED MACHINES from 12-13-2013
Hello CNC Friends, the following machines are now offered on our online marketplace for used machines: 1 Centre lathes 2 CNC-lathes (2-axes) 1 Vertical borer, single column 6 Machining Centers...
View ArticleNeed Help! Need single phase VFD for 2/3(0.667) hp motor. What are my options?
My mill uses a single phase 120V 2/3(0.667) hp motor and I need variable speed control. What are my options? I'd prefer to do this on a budget.
View ArticleCorrect Stepper Motor Driver Board Switch Settings
I was wondering if someone might be able to assist me in deciphering what the switches on my Stepper Motor Driver Board do. Here is a link to the manual for the driver board: LINK:...
View ArticleNeed Help! any one in fla. near cocoa.area
any one that is useing mach 3 i could use some help in set up thanks ron
View Articlefanuc 0-mb ladder
Someone has the control ladder fanuc 0-mb the problem I have is as follows: None of the axes move after starting the control and activate the servo drives, try movements in all modes but can not move...
View ArticleClik here to view.
Remeber your first
Remember when you set yours up the first time? remembeyourfirst.JPG Some assembly required! Any hints and or thoughts on final assembly, cleaning and prep not well covered in manual? Or if I could I...
View ArticleGenerating .gpx post-processor
Hi guys! anyone know how to generate .gpx post-processor aside from asking SolidCAM people to do it?
View ArticleJust ordered the last melon (Torus)
Thanks to all of the people who answered my questions on the Novakon mills over the last two months, I just placed an order for Novakon's last Torus milling machine. Although there wasn't a crowd...
View ArticleNewbie Rigid column X2 mill spacer?
Take the LMS solid column mill for example, other parts of the world it is an SX2 or what not, but with a solid non tilting x2 based mill, is there a reason no one has put a spacer between the base and...
View Articlenew guy
hi folks,, im interested in cnc controls I have a tos 25 fnk .. mew to me. and a Colchester 1550 lathe I also collect restore, and use woodworking equipment.. my latest prize is a wadkin PP saw,,18...
View ArticleNeed Help! New to artcam pro.
Hello every body i own a techno hd series cnc router and wants to learn artcam pro for 2d and 3d carving work. What is the best way to start? Need link for videos to start learning or ebook. M.Abid...
View Article