Kelly LaPeyre & Ray Harshberger
I have been trying to send updated drawings to you and it seems the email addresses i have are not good. If you get this message write me at stevehuck@hotmail.com so I can update my records and get you...
View ArticleHello CNC instructor looking for some help
After many years of not using CNC machines in back at it. My new shop has a hass mini mill, 3x kent cnc mills, 5x lathes, Small heat treating furnace, 6x Surface grinders, 3Dprinter. i'm trying to get...
View Articleneed student cnc materials and ideas for student lessons and projects
After many years of not using CNC machines in back at it. My new shop has a hass mini mill, 3x kent cnc mills, 5x lathes, Small heat treating furnace, 6x Surface grinders, 3Dprinter. i'm trying to get...
View ArticleClik here to view.
Need Help! Sanyo Denki CW/CCW Step direction Mode Mach3 question
I have a router wired with Sanyo Denki Q series drives and Motors. The motors spin fine with the Q setup software when connecting to each drive. I was going to control the router in LinuxCNC using a...
View ArticleNeed A Quote Need a PC board for a Brother EDM Model: HS-3100
Looking to purchase a WSTD board for a Brother EDM Model: HS-3100 Board part Number is B52J009-4, part number from Charmille is 63366071.
View ArticleNeed Help! Help with Mach 3 setup
IN the directions for the 540 it says to set mach 3 to 2 rev per second and turn the trim pot on the 540. How do I set mach 3 to run my motors to 2 revs per second?
View ArticleClik here to view.
Telemecanique E-Stop
Last year I bought this E-Stop which I did not use but planing to use now however I find the switch part when I twist it into the base it wobbles a lot like it is very loose and I wonder if the switch...
View ArticleClik here to view.
Problem laser tube fires only with test button!!
im trying to make my laser tube on/off using z axis dir (controlled with mach3). when im pressing the test button on the power supply there is red led turning on. i wired z axis dir to the high ttl on...
View Article5 axis breakout
Does anyone know of a way to check that each of the 5 axis on my breakout board are working as they should? I caused an arch on a machine I am building and the Y axis does not seem to be working...
View ArticleHigh Performance Controller on a budget???
Hi there, I need pointing in the right direction. I have very little electronics experience so I'm kind of out of my comfort zone here. The simplistic, probably quite vague question is, can you make a...
View ArticleJust In CNC knife die board router abandon laser way diemaker's complete...
Our steel rule die board router system completely replace the traditional laser cutting way for cutting die made of wood, acrylic, MDF, plastic, etc, support various kerf gap of die board, such as:...
View ArticleHere's what I've got, what am I missing?
Hi cnczone.com! I am building a desktop CNC machine, and I have ordered my parts. Would you kind folks take a look and see if I am missing anything? For the machine itself I bought the Shapeoko...
View ArticleNeed Help! parameter list for Shizuoka B-3V
Need help, . I have a un-complete parameter list for Shizuoka B-3V 410 . The info I have is Fanuc O-MC .. PC or PMC Parameter list. Thanks, Send me to alexrodal@yahoo.com
View ArticleHaving Trouble with Mach3 and windows 7 Parallel port
hello all, I am new to CNC , but not the concept. I am a self proclaimed electro mechanical engineer. I build lot on robots and under stand the principles behind stepper control. I have just bought the...
View ArticleUpgrade suggestions from a Dynapath 5c
I have an old Monarch Courtland VMC with a Dynapath 5c controller on it. We occasionally prop the control cabinet door open with the Tyrannosaurus Rex bone that came with the mill. No, is was never...
View ArticleNeed Help! Fadal repair or not repair?
I was given a Fadal 2016L SN 9801161 Model 904-1L 10,000 rpm. The only investment I have in it is storage and moving. I've had it in storage for 4 years. I saw it run before we shipped it. The only...
View ArticleTapping heads.
I have an 1100 and want to do threading, both external and internal. 1. Internal - Tormach lists at least 3 (sure there are plenty of other brands), but not clear how to choose? I won't be using it...
View ArticlePost processor 5 axis
Hello, I'm looking for a post processor for 5-axis SolidCAM. Can someone help me please? Hello
View ArticleClik here to view.
Just In 2nd Annual Digital Fabber CNC Jamboree ...
Anyone interested in a whole lot of fun mixed with a little training? The 2nd Annual CNC Jamboree will be held at Long Lake Park Campground, Lakeville, Ohio the weekend of September 20th, 21st and...
View Articlehow to change tool post from 2 digit to 4 digit code for dynpath?
hey guys, i recently upgraded to a lagun 3516 that now has a tool changer (my previous machine was also dynapath but no tool changer). when i make a program and call out for tools, its giving them to...
View Article