G0704 column bolts?
Hi everyone, new to the forum and machining. Havent been in a shop since the old highschool days. I just got a g0704, cleaned it up, stand bolted to floor and the unit mounted on the stand. I aligned...
View ArticleClik here to view.
Build Thread Shonky's lasercut steel fixed gantry routerish milly type CNC...
Hi, I've been lurking around for a bit, but decided to share my build, and figured it was better to get input sooner rather than later. So, as with a lot of these builds that are a bit different, I...
View ArticleCNC Mogul
Hello, I am looking at the CNC Mogul and wonder if anyone has anything to say about the brand? Its fairly cheep at only $1300 but seems like it would be a decent enough machine for an entry level...
View ArticlePWM 12V 20A for TB-650 spindle
Hi, I recently got a Wolfgang Engineering TB-650 spindle and I am looking for a PWM unit to control the speed a little bit better. I got a 12V 20A power supply setup and the missing part is the PWM...
View ArticleThe Judgment of high quality portable CNC cutting machine
Since the year of 2007, the new product, portable CNC cutting machine, was launched from China. 5 years past, thousands of similar models have been spread in the global market. However, how to...
View ArticleProblem Anilam 1100m programing questions
Hi, I just bought a Eagle 400 CNC with the Anilam 1100m on it. It seems like a great machine but I just can't seem to get my posting right from Mastercam 8 (which has a built in post for the 1100m)....
View ArticleClik here to view.
workholding..
I'm struggling to not get chatter on a long piece I'm trying to machine. Its made from 1.25 x .5 x 9" 6061 rectangle, and is machined on all sides. I'm using two vises and holding it fully on both...
View ArticleMfin wiring
The P10 connector on the IO board has 4 pins. which 2 are used to connect the Mfin input. I have a TM2 and it did not came with the 4 pin recepticle and haas gave me the part # for the plug and so I...
View ArticleG96..but not the usual question
Sorry to be the annoying noob, but I've spent most of today trying to figure this one out (anyone who is an expert in SE Wisconsin on Macturns can make extra cash here by visiting me in Eagle....
View ArticleShoptask 1720 XMTC parts
Afternoon, I have a 1993 vintage Shoptask 1720 XMTC and am looking for an upgrade or plans for a lead screw reverse upgrade for this machine. I've contacted Shopmaster and been told that its no longer...
View ArticleInstruction Manual for Weike LC1390 please
Hello Just recieved an LC 1390 from Weike. In good shape, no broken parts. Everything seems to be there. Except the instructions for putting it together and setting it up! I think they are on a DVD...
View Articlehelp attaching chuck to shaft for tube cutter?
I trying to build a tube cutter and I basically need to attach a plain back 3 jaw chuck to a short shaft which will run though a set bearings and have a belt drive on the end for a stepper. This set up...
View ArticleTLO multiple heights 1 tool
Tool Length Offset Register: Hi All, Our shop has a HAAS TM3 which I use daily, I own a FADAL TM also. When using the Fadal, I can use different H offsets for any given tool For instance Tool 3 I can...
View ArticleNeed Help! Cnc turning distance rings-washers
Hi, I have to make thin brass washers. ID=9.5 mm, OD=16mm. Thicknes= 0.3 ; 0.5 ; 1 and 2mm (ID=0.374'', OD=0.629''. Thicknes= 0.0118'' ; 0.0196''; 0.0393'' and 0.078'') Is there some special trick to...
View ArticleWhy are table slats not at 45 Deg??
CNC plasma is all new to me, but I see lots of posts about problems with cutting the top of a whole slat of it lines up with the cut. Some solutions call for bowed slats, others I have seen have points...
View ArticleClik here to view.
Need Help! What's the best way to machine an opened slot?
I wonder what is the way you guys use to machine an opened slot? Like what's shown in the pic. Attached Thumbnails
View Articlemaintenance check warning
Anyone know how to reset or clear the maintenance check warning that keeps popping up on my HTC 400 (M plus control). I see the hours are at 1500 and almost 3000 for the short term and long schedule...
View Articlestar "*" hotkey setup
in Mach3 I'm jogging my cnc router with a usb numeric keyboard pad (the one with just numbers) and it works great, jogging x, y and z and homing but I need to have a "zero all axis" hotkey setup as...
View ArticleNeed Help! num720 and old bosch servo
if any one ave an information or datasheet for the this parts list NUM 720 controller DRIVERS: Bosch SM 10/20-TC DC 520V 10A 060840-105 SM 5/10-TC DC 520V 5A 060839 SM 5/10-TC 3/PE AC 380V 50HZ 060838...
View ArticleBulleri cnc
if any one ave an information or datasheet for the this parts list NUM 720 controller DRIVERS: Bosch SM 10/20-TC DC 520V 10A 060840-105 SM 5/10-TC DC 520V 5A 060839 SM 5/10-TC 3/PE AC 380V 50HZ 060838...
View Article