Emco Compact 5 toolpost help
I have just purchased an Emco Compact 5 lathe with a six station rotating toolpost. Can anyone tell me how to manually rotate this from the control panel, there is nothing in the manual about this. Any...
View ArticleReinshaw - How often to you check runout
As the title states how often do you check the runout of your probe? I've been pulling my hair out with a part where the indexing lines were significant ... the probe was the last thing I checked and...
View ArticleProblem Citizen B12-6 Alarm Messages.
Hello everyone. I am having trouble with a Citizen B12-6. We have had a part off detection switch get smashed up inside and this has caused the mc to have these stated alarms. 1000 Emergency Button...
View ArticleZ looses it's place
I have had this happen 3 times in the past week. It is down approximately .060" the tools I am using are 1/32 and a .020" ball mill. My cuts are .003" I have checked to see if anything is loose....
View ArticleClik here to view.
What does Hiwin means with dimensional tolerances?
Hiwin states about C (Normal) pecision rails a dimension tolerance of +/- 0.1mm of H and N. 1) Does this means that it can accept an installation error on the machine of +/- 0.1mm on width and height....
View ArticleNeed Help! How to drill in a carbide material
Hello, I want to drill a counterbore in a carbide material. How should i do that ? Should i do EDM or something else ? Thanks Ashish
View Articlequestion
Hello, my name is Alex and I have a question. At work, we talked about use of cutter compensation. Some had opinion that one always has to program centerline of the tool, use g41/g42 and then put...
View Articlequestion about G41/G42
Hello, my name is Alex and I have a question. At work, we talked about use of cutter compensation. Some had opinion that one always has to program centerline of the tool, use g41/g42 and then put...
View Articlequestion about G41/G42
Hello, my name is Alex and I have a question. At work, we talked about use of cutter compensation. Some had opinion that one always has to program centerline of the tool, use g41/g42 and then put...
View ArticleToshiba TB6600
I see the Toshiba TB6600 Stepping Motor Driver Board. Ebay item 170923696690 Someone used this? What experiences have on? I would like to know your comments on this drive. Document: TB6600HG.pdf...
View ArticleNewbie I've decided to buy a PCNC 1100...
As an introduction, I'm a custom gunsmith located in a VERY small rural town in South Georgia. Most of my business is internet based and my main focus is in building high end handguns for competition...
View ArticleNeed manual for Seibu SW-5000J
Hi! Need manuals and any info on Seibu Walter SW-5000J. Thank you in advance for any help. Also we have an EDM machine AGIE Agiecut 100, and need the electrical drawing for it. But we have user's...
View ArticleClik here to view.
Just In laser machines Sample
this samples is producted by laser engraving machine MT-L1290/MT-L1280,our products prices is low,our service is first-class, of course, we have a Professional technical，welcome to buy. if you want to...
View ArticleNew Machine Build Home Switches
Wiring Home switches , should Home switch be connected between Pin4 and Pin 10 on the encoder plug ? or should the switch be wired with a separate 5+ Volts , into the switch , then into pin 4 ? Vsd-e...
View ArticleClik here to view.
Need Help! 2D Engrave
The 2D Engrave is not showing the rapids from the end of one cut to the beginning of another.This was reported upon initial release.This is of big concern because of possible collisions with clamps and...
View ArticleClik here to view.
Problem Download label of version 17
Hi everybody. Yesterday my machine starts giving this error on the panel and no longer works =X it doesn´t respond to any command. the machine is an PC 13/90. Tks
View ArticleNeed Help! Cortini H105 controler 2437
I need help with my cortini H105 with 2437 controller I hope you excuse my english There are som problems using G33 treading The spindle cant find the speed i programed so it dont starts treading and...
View Article5 Axis Router for PE Foam
We are a packaging company. Most of our PE (polyethylene) foam is die-cut. However, when we need to cut a curve or a vertical angle we need to cut by hand. (We cannot source good quality curved die-cut...
View ArticleNewbie opinions needed
Guys , I am new here but have been looking at the Cnc Masters Baron xl mill , i am milling small parts from Aluminum , brass and occational stainless as a startup shop and need some insight if anyone...
View ArticleFirst cnc build almost complete...
Sorry, I couldn't load pictures of the build. Have to go through shutterbug or something. Well, for the most part it's a cantilevered design based on a pick and place platform found on ebay for $600,...
View Article