Quantcast
Channel: CNCzone.com- Largest Forums for CNC Professional and Hobbyist alike!
Viewing all 73344 articles
Browse latest View live
↧

Bridgeport knee and colum Interacts TNC 151-155 Axis Drive Setup

November 4, 2019, 12:08 pm
$
0
0
I found this going through some of my paper work and thought it would come in useful to someone.
It is instructions for tuning axis drive boards X, Y and Z.

I hope it helps !!

Attached Images
↧
Search

Need Help! OKK VP400 5 AXIS Z AXIS OFFSET ERROR WHEN MACHINE TURN A AND C AXIS

November 4, 2019, 1:07 pm
$
0
0
HELLO
TO ALL
I HAVE A PROBLEM IN THE MACHINING OF THE ROTARY AXLES OF AN OKK VP400 THE G54 IS ABOUT THE MASTER PART WITH THE A Y C AXES IN ZRN EXACTLY AT 0.026 THOUSANDS UP FROM THIS WHEN A MEASURE VERIFICATION IS CARRIED OUT IN THE FOUR FACES OF THE MASTER BLOCK MESURES AS FOLLOW :
SIDE 1 MEASURE 0.024 "
SIDE 2 MEASURE 0.030 "PLACED BELOW SIDE 1
SIDE 3 MEASURE 0.018 "
SIDE 4 MEASURE 0.033 "
THE MEASURES ARE ALWAYS PERFORMED WITH THE PART ORIENTED PLANE XY
I TRY TO MOVE THE PARAMETERS OF FANUC 19700,19701, 19702 AND NO CHANGES ARE ALREADY REMAINED. (THE PARAMETER CHANGES BUT THERE IS NO CHANGES PHYSICALLY)
THE GEOMETRY OF THE AXES A AND HAVE BEEN VERIFIED ITS PLANNING IS BELOW 0.010mm 0° AND 90°
I hope someone has information on how to enable the compensation of axes A and C OR WHY Z AXIS IS COMPENSATE IN THIS WAY I WILL APPRECIATE THE HELP
THANKS IN ADVANCE

↧
↧

Need Help! Parameter PCM TORNO MORI SEIKI SL25 FANUC 10T

November 4, 2019, 1:12 pm
$
0
0
HELLO WHO CAN HELP ME, WITH PHOTOS TO WRITE THE PCM PARAMETERS MANUALLY


TORNO MORI SEIKI SL25 FANUC 10T YEAR 1987

↧

How to set the origin at the corner of the stock?

November 4, 2019, 2:31 pm
$
0
0
It's been about 10 years since I've used MasterCam.
I'm trying to create a machine origin at the corner of the stock and it's kicking my A$$!
Last software I used was CamWorks, no problem, pick the corner.
I'm wanting to use the lower left corner for XYZ zero. This must be a common practice but it's like a secret everywhere I look:
Capture1.PNG

Attached Images
↧

Tormach 24R Router

November 4, 2019, 3:54 pm
$
0
0
Looks like Tormach is now in the router business. The 24R router a 2 x 4 foot cnc router.




Attached Images
↧
↧

Could a defunct flatbed printer be repurposed into a CNC?

November 4, 2019, 4:32 pm
$
0
0
Hey all, We're a small sign and graphics company that owns a now defunct 5'x10 flatbed UV printer whose manufacturer has abandoned all service parts, ink and support.

Basically the thing is a big work table now, but it is sturdy as hell, has machined side rails that the printhead gantry runs on and all the internal electronics and motors to do an X and Y axis as well as some vertical movements. It has a built in vacuum system to hold down materials.

I have no idea if it is of any interest to any ambitious DIYers here and hate to see it just go to the scrap yard.

If anyone has any interest, feedback or ideas of a good use of this thing, I'm all ears.

↧

1997 Daewoo LYNX 200A lost parameters. FANUC 21T

November 4, 2019, 7:40 pm
$
0
0
Hello everyone, I bought a Lynx and had a cpu problem. Bought a new board and the parameters are completely lost. I can not see the ladder either. Any advice on how to get them or buy them? Thanks in advance.
Regards
Ernie

↧

Fanuc 604 PC Alarm

November 4, 2019, 8:16 pm
$
0
0
Hello good day, i obtain this alarm in a Fanuc 6M control (604 PC Alarm), checking the manual maintenance, suggest change the pcb (pg51):

Cause Checking Countermeasures
PCB A20B-0008-0440 is faulty. Make sure that PCB setscrews are fastened. Replace the PCB.

I can obtain this pcb of other 6M, however i no have clear the functions of this:

Replace this pcb of other control 6M there may be compatibility?

Program of change tool is in this pcb?

regards
Renato

↧
Search

Language file

November 4, 2019, 9:09 pm
$
0
0
Is it possible to use double-byte characters such as Japanese for language files?

↧
↧

Language file [SOLVED]

November 4, 2019, 9:09 pm
$
0
0
Is it possible to use double-byte characters such as Japanese for language files?

↧

problem haas mikron vf500 alarm 160 low voltage

November 5, 2019, 12:49 am
$
0
0
Good Morning. I have a problem with a haas mikron vf500 from 1995. the machine whenever you turn on the servos and the voltage 160vdc arrives at the main board the alarm occurs and there is no possibility to remove it. if you open the doors the alarm with reset disappears. I close the doors and the alarm occurs again. I already controlled the voltage 160vdc and is always at 170vdc. I need to know where this alarm is controlled because from what I checked it looks like it's on the PCB card where the 160vdc comes in. I have no solution to the problem. I appreciate who can help me. thanks

↧

AIO Garage Project

November 5, 2019, 1:36 am
$
0
0
Hi All,

I'm a long time lurker - first time poster.
I built a small CNC about 4 years ago based on a Chinese 6040 frame, using parts (steppers, wiring and PSUs from old ATM machines) and used Mach3 and a cheap BOB for the controller

I enjoyed working on CNCs so much I quit ATMs and managed to get a job as a CNC technician - I now work fulltime on SCM and CMS 3-6 axis industrial machines.

I quickly lost interest in the limitations of the 6040 and sold it.
I've finally got around to designing my own machine. It is designed to fit in a single garage with a machining area of 1420x1420x200mm.
I wanted to make an all in one universal machine built rugged enough to be reliable and not have to spend most of my time making adjustments...
The machine will have 4 interchangeable heads - a 55Amp Plasma, 2.2kw spindle, 15w laser and an air scribe.

The thought of lead screws and skateboard bearings makes me cringe, so decided to go for 16mm ball screws and Hywin clone 20mm linear bearing rails.

The X axis will have a total of 4x20mm rails

I TIG welded the base from 50mm/3mm box section and have used 80x160mm aluminium extrusions for the X and Y axis rails.

I have finally got all the parts together and thought I'd post the build progress here and share the design/dxfs etc if anyone is interested.

↧

New Product 1530 linear carousel atc cnc router for furniture cutting

November 5, 2019, 1:58 am
$
0
0
1530 4 axis atc cnc router wood machine for wood cabinet making

Cost effective price and professional suggestions for you, Contact us now by whatsapp +86 15064026772, email
manager@elephant-cnc.com






# 1500x3000x400mm working size;
# Italy Original 9.0KW HSD ATC Spindle;
# 12pcs carousel ATC+12pcs HSK-63F tool holders, 750w japan yaskawa servo motors
Customized gantry and steel support;
# Taiwan DELTA 11.0kw Inverter;
# Taiwan SYNTEC11MB Control System;
# 850w Japan Yaskawa servo motors and 1000w drivers;
# 25mm Sweden ABBA Linear rails;
# Helical rack and pinions;
# Taiwan TBI Ball screws;
# Vacuum Table with t slot; German Becker KVT3.140 4.0KW vacuum pump included;
# Automatic oil lubrication system;
# Japan OMRON Limit Switch;
# High Flexible towline,fire-resistant double-sheathed Shanghai Cardiff cable;
# ARTCAM Software;
# 4th rotary axis: 300mm Diameter and 2500mm Length ( With 850W Japan Yaskawa motors )
# France Schneider safety switch;
# 1.5kw Europe CE Standard double bags dust collector;

Attached Images
↧
↧

Need Help! need help for Connect the machine to the laptop

November 5, 2019, 6:08 am
$
0
0
Hello evryone
I have a problem identifying the machine cnc3018 with cable for the laptop .
When I connect the machine cable to the laptop. Windows does not recognize the machine. This message appears
(( look at the picture ))

Windows Message
https://1.top4top.net/p_1402cvzj41.png

Note . that when i run the machine with Offline remot operates without problems ..
The cable also has no problems

please help

Picture of the control board
https://2.top4top.net/p_14026st1s1.png

Attached Images
↧

Break away torque calculation of lock nut against rotating/acceleating bolts?

November 5, 2019, 7:42 am
$
0
0
I have a Scenario where my lock nut is tightend using a prevailing torque of 14 Nm (as mentioned by the manufacturer) on to the rotor placed between bearings (But the tightening direction and the rotor rotating direction is same unfortunately). The lock nut is loosened after particular life cycle of usage as the rotor rotates with a acceleration of 1230 rad/sec and every time it starts, the sudden acceleration loosens the lock nut. Is there a simple approch to calculate a appropriate prevailing torque for this situation, so that the lock nut does not loosen up when the rotor starts accelerating towards it's max RPM of 9400 in 1 second?

↧
Search

Break away torque calculation of lock nut against rotating/acceleating bolts?

November 5, 2019, 7:46 am
$
0
0
I have a Scenario where my lock nut is tightend using a prevailing torque of 14 Nm (as mentioned by the manufacturer) on to the rotor placed between bearings (But the tightening direction and the rotor rotating direction is same unfortunately). The lock nut is loosened after particular life cycle of usage as the rotor rotates with a acceleration of 1230 rad/sec and every time it starts, the sudden acceleration loosens the lock nut. Is there a simple approch to calculate a appropriate prevailing torque for this situation, so that the lock nut does not loosen up when the rotor starts accelerating towards it's max RPM of 9400 in 1 second?

↧

Any get their kit, WHEN FLA said they would?

November 5, 2019, 7:49 am
$
0
0
I'm looking into one of FLA's 2'x3' FLA100 Kits. Their site says "IN STOCK", and "GUARANTEED TO SHIP NEXT DAY"...

Has anyone actually got a tracking # the next day?

I've heard HORROR stories about timelines and quality...but I also know forums are usually more geared towards vocalizing BAD, than GOOD.

↧
↧

New Machine Build Bodor machine ,good machine,good service

November 5, 2019, 8:41 am
$
0
0
We just finish the building of the new machine ,6kw ipg,S4020.
First ,we are very satisfied with the machine .The machine runs steadily .The cutting qulity is very good.
.We are happy with progress so far, maybe fun will start when Sunny has gone to China! We have found working with Bodor very easy and out installation engineer Sunny has been very good and helpful. Hopefully we will be in production soon and get up to speed over the next week or two.


↧

Budget CNC Mill under $2000?

November 5, 2019, 9:10 am
$
0
0
Hello, I am new to the forum, so if I break any rules please let me know. A little about me I currently a college student(Major:Industrial engineering Minor: Manufacturing Engineering, and automation certification) and interning with a large company as an industrial engineer the last year. I have experience with manual and cnc lathes and mills, much nicer than I can afford, but am looking for a cnc mill that I can cut stainless around .001 accuracy. I want am taking 18 credit hours next semester, so a full time job is probably out of the question, but I was thinking that if I could do some milling jobs, pay off the machine, then I could make some extra cash during school. I have also considered going the fiber laser route, but not having much experience with lasers and their life I am a bit weary. Trying to keep the machine under $2000 not including tooling. Thanks!

↧

RosettaCNC 1.6.9.55 Released

November 5, 2019, 9:40 am
$
0
0
For those who have already installed RosettaCNC 1.6.x it is now possible to update online 1.6.9.


Changelog:



  • Improved Antialiasing Levels from 4 to 7 (2x, 2xHQ, 4x, 4xHQ, 6x, 8x, 16x).
  • Improved GCode languange:
    • In Looping & Branching added ELSE in IF THEN.
    • In G65/G66 added local named parameter _args to get macro arguments.
    • In named parameters added new EXISTS[] check to know if parameter exists.

  • Probe Scanner 3D changes:
    • Added new Static Data Analysis panel with new post-scan filter options.
    • Probe Scanner 3D with Laser get more points to permit post-scan filter options.
    • Increased performance of data points acquiring phase.
    • Fixed 3D Probe Scanner STL Mesh file saving when file name contents dot chars.

  • Added support of X/Y/Z translations in master/slave main sections of VMs.
  • Added a warning message if W7/W8 OS is using System Font Size different than 96 DPI.




Improved Antialiasing Levels from 4 to 7 (2x, 2xHQ, 4x, 4xHQ, 6x, 8x, 16x)
The graphic quality of the route and the virtual machine has been increased thanks to the increase in Antialiasing levels from 4 to 7.


Improved GCode languange
The G language has been extended to support ELSE in IF THEN decision blocks.
Now within a macro / sub you can access the value of the arguments using the named parameters:


Code:
G65 P1000 A10 B20 X30
...
M2


O1000
IF [# <_ args.A> GT 10] then ....


; or with standard FANUC access


IF [# 1 GT 10] then ...
M99

Added the command EXISTS [] to know if a named parameter is already in use.


Probe 3D Scanner changes
Various improvements in the 3D scanning / 3D Surface flatness area, such as increasing the sampled points along the scan axis.
This allows you to get more details and be able to do post-processing of the scan through the new panel
Static Data Analysis .


Scan





Post-scan panel





Filtered scan result





Through the panel of Static Data Analysis it is possible to open scans made in the past, view them and operate new filtering technologies that will be promptly added to further software development.

↧
Viewing all 73344 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>