I managed to jog my Z too far (Towards the table) and now I am stuck with a E-stop alarm. Is there an easier way to jog it back off the limit other than removing the switch? The control is a yasnac i80m. I think its a 1996.
↧
Need Help! Kitamura mycenter 0 axis over-travel
↧
CNC Router RCA1325, with auto feeding and downloading
↧
↧
RCA1530 IS IN CANADA
Auto loading and unloading center RCA1530 with auto labeling machine
![]()
↧
Spindle works only after closing and opening the mach3
Hi there
In my previous post I think i couldn't explain clearly my Spindle problem,
My spindle works only after I close and open the mach3, By doing so (opening the mach3), I noticed that in "Spindle Speed" Section of the First Tab (Program RunAlt-1) As you know there is a Button by name of "Spindle CW F5" and under this buttom there are some DROs that one can Enter RPM in it The RPM Values are "at the time of opening" all Zeros. At this point If I push the "Spindle CW F5" Button and then enter some RPM values in "spindle speed" DRO , The Spindle starts Running and I can Increase or decrease its RPM speed.
But If I try to run a code like usual which is by loading a G Code program and then pushing the start Button, The axis move But My Spindle would not start, It appears that the spindle does not respond to the M3 Command of the G code, and at this point even if I push the "Spindle CW F5" Button, the Spindle would not start, also the DROs under this "Spindle CW F5" Button have some values in them from the G code that even if I try to change them they would not change. At this point I have to Close and open The Mach3 in order to start the spindle.
Any recommendations or suggestions that what is going on here?
should mention that all these happened recently, It was working Fine before.
Regards
Jhonansaro
In my previous post I think i couldn't explain clearly my Spindle problem,
My spindle works only after I close and open the mach3, By doing so (opening the mach3), I noticed that in "Spindle Speed" Section of the First Tab (Program RunAlt-1) As you know there is a Button by name of "Spindle CW F5" and under this buttom there are some DROs that one can Enter RPM in it The RPM Values are "at the time of opening" all Zeros. At this point If I push the "Spindle CW F5" Button and then enter some RPM values in "spindle speed" DRO , The Spindle starts Running and I can Increase or decrease its RPM speed.
But If I try to run a code like usual which is by loading a G Code program and then pushing the start Button, The axis move But My Spindle would not start, It appears that the spindle does not respond to the M3 Command of the G code, and at this point even if I push the "Spindle CW F5" Button, the Spindle would not start, also the DROs under this "Spindle CW F5" Button have some values in them from the G code that even if I try to change them they would not change. At this point I have to Close and open The Mach3 in order to start the spindle.
Any recommendations or suggestions that what is going on here?
should mention that all these happened recently, It was working Fine before.
Regards
Jhonansaro
↧
biesse errors
hey guys new here.
im getting an error on my biesse saying for the spindle with automatic tool change the direct position is not valid
but only the magazine positions. Would anyone know what this means cheers..
im getting an error on my biesse saying for the spindle with automatic tool change the direct position is not valid
but only the magazine positions. Would anyone know what this means cheers..
↧
↧
Edge banding machine RC-E07
wechat:+86 16653128170
Email?cnc05@roc-tech.com
Edge banding machine RC-E07
Pre-milling,gluing,end-trimming,rough-trimming,fine-trimming,corner-rounding, scraping, buffing.
![]()
Email?cnc05@roc-tech.com
Edge banding machine RC-E07
Pre-milling,gluing,end-trimming,rough-trimming,fine-trimming,corner-rounding, scraping, buffing.
↧
Haas DS30Y Post Needed
Hello,
I'm in need of a post for my Haas DS30Y. I don't need one that is 100% going to run my machine. I am looking for something at least close. I can make minor post modifications if need be.
Thank you
I'm in need of a post for my Haas DS30Y. I don't need one that is 100% going to run my machine. I am looking for something at least close. I can make minor post modifications if need be.
Thank you
↧
hitachi seici ht23rIII turning center seicos l multi
Good day.
Need infornation how to calibrate q-setter
Have no instruction manual
I do not know- may i change some parametrs or another way to calibrate q-setter
Please, help if you have any idea
Alex Koifnan
Odessa
Ukraine
Need infornation how to calibrate q-setter
Have no instruction manual
I do not know- may i change some parametrs or another way to calibrate q-setter
Please, help if you have any idea
Alex Koifnan
Odessa
Ukraine
↧
Yaskawa SigmaWin+ 5 and RS232 to USB adapter - any experience out there?
I'm trying to use Yaskawa SigmaWin+ 5 to communicate with SGDB drives. I've brought a rs232 to USB adaptor but plugging it into the drive and searching yields 0 drives found. I've tried tweaking the port settings to the settings in the manual but that doesn't help either. The manual makes note of a kind of yaskawa specific cable and it's no trouble to make one up but it doesn't look like it's any different to a standard null modem cable so I'd imagine it's no different than just plugging the adaptor directly into the drive.
Anyone got any experience with this kind of stuff? I've never had much to do with serial connections.
Any help greatly appreciated.
Cheers
Sam
Anyone got any experience with this kind of stuff? I've never had much to do with serial connections.
Any help greatly appreciated.
Cheers
Sam
↧
↧
New Listing Site CNCMachines.com
We just launched a new listing website for CNC Machines, Included in your listing is a chat feature to talk with interested buyers, a CNC expert to help you with negotiations and logistics and best of all you don't pay until your machine sells. You can list metalworking machines, fabrication, parts, and tooling.
You can register to buy or sell at CNCMachines.com
If you want more detailed info feel free to pm me here or email me at jonathan@cncmachines.com
Have a great Friday!
Jon Alonso ( Learn More About Me :) )
P.S. I am open to feedback, It makes our website better and helps me identify ways to make it easier for manufacturers to sell and buy without all of the "dealer" hassles
You can register to buy or sell at CNCMachines.com
If you want more detailed info feel free to pm me here or email me at jonathan@cncmachines.com
Have a great Friday!
Jon Alonso ( Learn More About Me :) )
P.S. I am open to feedback, It makes our website better and helps me identify ways to make it easier for manufacturers to sell and buy without all of the "dealer" hassles
↧
Mach 4 lathe
Looking for a tool changer macro for Mach4 machine is a lathe with 6 position tool changer .No air cylinder .Pawl locks turret ,only moves one directing every 60 degrees then backs up a few steps against the pawl. Would be will to pay for the working Macro.
↧
DM3000 Macro
Needed .A Macro for a Mach conversion .Trying to get turret working .Have it connected as axis .Can manually move turret looking to automate the toolchange from within the program with M06 Any help would be great thanks to all ..!
↧
Error with Brother HS-300 Wire EDM
We have encountered an error with our Brother HS-300 wire EDM after removing and repairing the coolant pump.
Once the pump was repaired the status light shows an error but does not display a cause or error type on the diagnostic screen. Due to the error the controller will not allow for jog, water pumping, or wire feeding.
I have been trying to find a way to reset the machine to factory settings in hope that it will clear this error.
Any help from anyone would be appreciated!
Thank you.
Once the pump was repaired the status light shows an error but does not display a cause or error type on the diagnostic screen. Due to the error the controller will not allow for jog, water pumping, or wire feeding.
I have been trying to find a way to reset the machine to factory settings in hope that it will clear this error.
Any help from anyone would be appreciated!
Thank you.
↧
↧
Oil Matic MPSD what is it for and how to set it?
Hello! I have Oil Matic MPSD-07-N-CE on my Okuma B200. I dont have any books or manuals for the oil matic and i cant find much on the internet. Found in PDF what MPSD stands for:
M is for...model ? :D
P is for High Precision
S is for Cooling Main spindle
D is for With tank
Ok so in the morning the temperature shows around 23°C (outside temp is around 20°C) and later it shows around 28-29-30°C.
I also found some settings in the PDF. By holding ENT and changing the next value to 10 (from 11) a new menu appeared before my eyes! It was "C" menu which was set to 45°C !? I set it to 25°C and it was holding that for about an hour (then my shift ended) +-0.1°C. I've never seen it holding one temperature before. Did i turned it ON ? Did i do something i wasn't supposed to do ? What did i do ? :eek: May someone explain me the benefits of holding constant 25°C and why am i cooling the main spindle for ?
M is for...model ? :D
P is for High Precision
S is for Cooling Main spindle
D is for With tank
Ok so in the morning the temperature shows around 23°C (outside temp is around 20°C) and later it shows around 28-29-30°C.
I also found some settings in the PDF. By holding ENT and changing the next value to 10 (from 11) a new menu appeared before my eyes! It was "C" menu which was set to 45°C !? I set it to 25°C and it was holding that for about an hour (then my shift ended) +-0.1°C. I've never seen it holding one temperature before. Did i turned it ON ? Did i do something i wasn't supposed to do ? What did i do ? :eek: May someone explain me the benefits of holding constant 25°C and why am i cooling the main spindle for ?
↧
Need Help! Error with Brother HS-300 Wire EDM
We have encountered an error with our Brother HS-300 wire EDM after removing and repairing the coolant pump.
Once the pump was repaired the status light shows an error but does not display a cause or error type on the diagnostic screen. Due to the error the controller will not allow for jog, water pumping, or wire feeding.
I have been trying to find a way to reset the machine to factory settings in hope that it will clear this error.
Any information or advice offered would be helpful!
Thank you.
Once the pump was repaired the status light shows an error but does not display a cause or error type on the diagnostic screen. Due to the error the controller will not allow for jog, water pumping, or wire feeding.
I have been trying to find a way to reset the machine to factory settings in hope that it will clear this error.
Any information or advice offered would be helpful!
Thank you.
↧
Mitsubishi M700 - ATC
Hi, i'm quite new in this field of work.
I'm trying to setup an ATC with our CNC.
Right now i'm stuck trying to figure out how to create custom M function. I created a custom Marco witch do the tool change, but i need to link it to the M06 function for our machinist well being.
Could anyone point me how to do this ?
Thanks a lot.
I'm trying to setup an ATC with our CNC.
Right now i'm stuck trying to figure out how to create custom M function. I created a custom Marco witch do the tool change, but i need to link it to the M06 function for our machinist well being.
Could anyone point me how to do this ?
Thanks a lot.
↧
Selecting one of multiple layered tool paths
Does anyone know of a trick to select one of several tool paths stacked on top of each other for editing.
My problem I sometimes have parts that need milled out, but may also have an edge treatment on one or more sides (just an open offset). These tool paths end up overlaping and look like one and if I need to edit one or the other sometimes I find that I can not get to one of them. Double clicking on the tool path to edit it always brings up the other tool path that I don't want to edit.
So far the only way I've found to get to and edit the path I want is to start deleting stuff until I can get to the path I need to edit. That is very time consuming to go back and restore the parts I had to delete to edit the one tool path I couldn't get to.
My problem I sometimes have parts that need milled out, but may also have an edge treatment on one or more sides (just an open offset). These tool paths end up overlaping and look like one and if I need to edit one or the other sometimes I find that I can not get to one of them. Double clicking on the tool path to edit it always brings up the other tool path that I don't want to edit.
So far the only way I've found to get to and edit the path I want is to start deleting stuff until I can get to the path I need to edit. That is very time consuming to go back and restore the parts I had to delete to edit the one tool path I couldn't get to.
↧
↧
Need Help! LEADWELL LTC 20 AP FANUC OTF
I have restored the lathe parameters that I saved couple monts ago. I do not have the 900 parameters who I have forgotten to copy. After restoring the parameters, the DUPLOMATIC turret no longer wants to work. Is it possible for the 900 parameters to influence its action?
A specialist's advice would be good for me. If you have an LTC lathe you can help me with the 900 parameters?
Thanks
A specialist's advice would be good for me. If you have an LTC lathe you can help me with the 900 parameters?
Thanks
↧
CamWorks UPG source file?
I am trying to open the MT4AXIS-TUTORIAL.SRC file in UPG. Is there a reason this file will not open?
It seems to have all the support files in the same folder?
There is also a CTL file in the CamWorks post library?
It is saying this file was not created using UPG or wrong file type. If I drag it on the shortcut it comes in blank.
It opens in EC Editor and looks like it should open.
John
It seems to have all the support files in the same folder?
There is also a CTL file in the CamWorks post library?
It is saying this file was not created using UPG or wrong file type. If I drag it on the shortcut it comes in blank.
It opens in EC Editor and looks like it should open.
John
↧
Need Help! Fuji Frenic 5000W
Can someone help with instructions, how to setup Fuji Frenic 5000W Drive
thanks
dj
thanks
dj
↧